R&S
FSV3030 Signal & Spectrum Analyzer
Frequency range: 10 Hz to 30 GHz
Phase noise: < -114 dBc at 1 Hz
(f = 1 GHz, 10 kHz offset, B710 option)
DANL (at 1 GHz): < -162 dBm/Hz
Maximum analysis bandwidth: 200MHz
Multi-touch enabled graphical user interface, SCPI recorder, and event-based operation
Multiple analog and digital signal analysis options, including 5G NR signal analysis
Definitions General Product data applies under the following conditions:
"Specifications with limits" above. However, product performance in this case cannot be warranted due to the lack of measuring equipment traceable to national metrology standards. In this case, measurements are referenced to standards used in the Rohde & Schwarz laboratories. Specifications without limits Represent warranted product performance for the specified parameter. These specifications are not specially marked and represent values with no or negligible deviations from the given value (e.g. dimensions or resolution of a setting parameter). Compliance is ensured by design. Typical data (typ.) Characterizes product performance by means of representative information for the given parameter. When marked with or as a range, it represents the performance met by approximately 80 % of the instruments at production time. Otherwise, it represents the mean value.
Nominal values (nom.) Characterize product performance by means of a representative value for the given parameter (e.g. nominal impedance). In contrast to typical data, a statistical evaluation does not take place and the parameter is not tested during production. Measured values (meas.) Characterize expected product performance by means of measurement results gained from individual samples. Uncertainties Represent limits of measurement uncertainty for a given measurand. Uncertainty is defined with a coverage factor of 2 and has been calculated in line with the rules of the Guide to the Expression of Uncertainty in Measurement (GUM), taking into account environmental conditions, aging, wear and tear. Device settings and GUI parameters are designated with the format "parameter: value". Non-traceable specifications with limits, typical data as well as nominal and measured values are not warranted by Rohde & Schwarz. In line with the 3GPP standard, chip rates are specified in million chips per second (Mcps), whereas bit rates and symbol rates are specified in billion bit per second (Gbps), million bit per second (Mbps), thousand bit per second (kbps), million symbols per second (Msps) or thousand symbols per second (ksps), and sample rates are specified in million samples per second (Msample/s). Gbps, Mcps, Mbps, Msps, kbps, ksps and Msample/s are not SI units.
• Three hours of storage at ambient temperature followed by 30 minutes of warm-up operation
• Specified environmental conditions met
• Recommended calibration interval adhered to
• All internal automatic adjustments performed, if applicable Specifications with limits Represent warranted product performance by means of a range of values for the specified parameter.
These specifications are marked with limiting symbols such as , ≥, ±, or descriptions such as maximum, limit of, minimum. Compliance is ensured by testing or is derived from the design. Test limits are narrowed by guard bands to take into account measurement uncertainties, drift and aging, if applicable. Non-traceable specifications with limits (n. trc.) Represent product performance that is specified and tested as described under
Q: Who are we?
A: Dongguan Qihang Electronic Technology Co., Ltd. is a professional company engaged in the research and development, sales, maintenance, measurement, technical consulting, and provision of Bluetooth RF testing systems and testing solutions for RF, microwave, and electronic testing instruments.
Q: How to ensure quality?
A: Before shipment, our quality inspector will conduct a comprehensive test of the product to ensure that the customer receives the instrument without any issues
Q: What can I buy from here?
Q: We can provide various instruments for Keysight, Ceyear, Tektronix, Rohde&Schwarz, Agilent, Keithley, Anritsu, and Lecroy
Q: Why do you want to purchase from us instead of other suppliers?
A: We have good prices and the advantage of overseas warehouses, which can make the goods arrive faster. And a good after-sales solution.
Q: Where do you ship from and how long is the delivery time?
A: Shipping from Guangdong, China, with a delivery time of 15 working days after getting the payment.
Audited Supplier 
){kind=link}